Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung Nächste ÜberarbeitungBeide Seiten der Revision | ||
ovi40_uiboardbuild [16.01.2018 13:55] – df9ts | ovi40build:uiboardbuild [25.01.2018 15:50] – df9ts | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
+ | {{tag> | ||
- | ==== IVI40 UI Board ==== | + | ===== Building the UI V1.8 Board ===== |
- | Das UI Board beinhaltet den Hauptprozessor (MCU), Stromversorgung, | + | |
- | Auf das UI Board werden Displayboard und RFboard direkt aufgesteckt (Pfostensteckverbinder) | + | ==== OVI40 UI V1.7 Documents ==== |
- | ==== OVI40 V1.8 Bausatz ==== | + | **UI V1.7 documents are provided for information only**. Please primarily use the V1.8 documents for building the UI V1.8 board. |
- | Der Bausatz beinhaltet Bauteile in Tütchen sortiert, Leiterplatte sowie Display | + | |
- | |[{{: | + | |
+ | | ||
+ | | ||
- | {{ : | + | Please note that the component placement docs are searchable pdf documents. During soldering they can be used to quickly find a component' |
- | ==== Aufbauhinweise | + | ==== OVI40 UI V1.8 Documents |
- | < | + | |
- | < | + | |
- | < | + | |
- | ==== Unterlagen: OVI40 UI V1.7 ==== | + | * {{:projekte: |
- | UI V1.7 war die Beta Test Version der UI Platine. Es bestehen nur wenige Unterschiede zwischen V1.7 und V1.8 (der ausgelieferten Bausatz Platine). Die V1.7 Unterlagen sind deshalb interessant zum Vergleich und als Ergänzung. | + | * [[: |
+ | * {{: | ||
- | < | + | ==== OVI40 UI V1.8 Kit Contents ==== |
- | OVI40 UI V1.7 Schaltbild: {{: | + | The kit contains |
- | OVI40 UI PCB bottom layer: {{: | + | |< 60% 33% 33% 33% >| |
+ | |[{{:projekte: | ||
- | OVI40 UI PCB top layer: {{: | + | ==== Assembly and Soldering ==== |
- | ==== Unterlagen: OVI40 UI V1.8 ==== | + | The graphics below - UI V1.7 with 3.2" Display - give an impression on how the finished |
- | Im Vergleich zur V1.7 UI kommt bei der UI V1.8 folgendes dazu: | + | |
- | * unter dem Display ein weiterer zusätzlicher Taster | + | |
- | * die beiden STEP Taster unterm VFO können in zwei verschiedenen Positionen eingelötet werden. Entweder klassisch leicht nach oben versetzt wie beim mcHF oder tiefer und damit in einer Flucht mit den 6 Funktionstasten. | + | |
- | OVI40 UI BoM: [[: | + | |< 95% 50% 50% >| |
- | BoM von F4HTX Francois mit Bauteiletütchen Nummern: | + | | [{{:ovi40build:ui_top_3d.png?400|UI Board V1.7 mit 3.2" Display)}}] |
- | ==== STM32F76X_ZIT vs. STM32H743ZIT6 | + | === Please read Errata carefully |
- | Der Bausatz enthält den STM32F76X_ZIT. Der neue STM32H743ZIT6 kann eingesetzt werden, wird aber nicht mitgeliefert. | + | |
- | Die H7 - MCU wird zukünftig der Standard sein, die F7 MCU wird " | + | |
- | ==== Flashen des UI Boards ==== | + | Make sure to read the [[:ovi40build: |
- | Der UHSDR Bootloader hat 2 Modi: er kann über USB Memorystick geladen werden oder über den sogenannten DFU Modus | + | |
- | Weiter Details sind hier erklärt: https:// | + | < |
+ | === IC Device Markings === | ||
+ | </code> | ||
- | Alles, was auf " | + | The smaller ICs can be identified by device mark. The following device marks are used: |
- | <bootnote>ToDo SW von wo (BL & FW)</ | + | |< 45% 25% 25% 25% 25% >| |
- | Bootlader: | + | |
- | Firmware : | + | |
- | Alles, was auf .bin aufhört, muss entweder mit dem ST-Link (bootloader updaten) oder mit dem USB-Stick (firmware updaten) gemacht werden. Zusätzlich kann man die firmware auch mit dem ST-Link updaten (.dfu). | + | |Typ |Device Mark |Schematic |
+ | |LP5907_Q1 | ||
+ | |BAV70 | ||
+ | |BC857B | ||
+ | |BAS85 | ||
- | < | + | === MCU STM32 "Pin 1" marking === |
- | === Bootloader laden === | + | Please understand the correct orientation of STM32 MCU Pin 1. There are two markings on the IC. Please not the text printed on MCU to find the correct Pin 1: When reading the text Pin 1 is on bottom left corner. |
- | Siehe auch [[https:// | + | |
- | Stromversorgung dazu 5 Volt Pin 28+ , Pin 30 Gnd) | + | [{{: |
- | === UHSDR Firmware laden === | + | < |
- | Nachdem im DFU mode (J6) der neueste Bootloader geladen wurde (bl-40SDR.dfu): | + | |
- | - +8V on JP1 pin 29 - zur Stromversorgung des USB stick! | + | </ |
- | | + | |
- | - +5V on JP1 pin 28 legen - um bootloader zu starten | + | The kit is shipped with STM32F76X_ZIT |
- | - USB stick in USB port stecken | + | |
- | - Warten bis FW upload fertig ist | + | Comparison of MCUs: |
- | | + | |
- | - +5V aus und wieder einschalten für OVI40 UI board reboot. | + | |< 90% 25% 25% 25% 25% >| |
+ | |||
+ | | | ||
+ | | | ||
+ | |Flash[kB] | ||
+ | |RAM [kB] |192 |512 |1024 | | ||
+ | |Clock[MHz] | ||
+ | |FPU |single | ||
+ | |Pins |100 |144 |144 | | ||
+ | |DMIPS | ||
+ | |||
+ | === EEPROM IC7 orientation === | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | This is where the dot is printed. Also the edge of the case is slanted near the 1-4 pins. See [[http:// | ||
+ | |||
+ | === Prevent short cut with back up battery holder === | ||
+ | |||
+ | One of the connection pins of the battery holder might touch ground connection of a rotary encoder. Make sure to cut this pin flush with PCB surface **before soldering** | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | === Polarised capacitors === | ||
+ | |||
+ | Please observe mounting orientation of tantal and electrolytic capacitors. Markings on the capacitors are explained [[http:// | ||
+ | |||
+ | === Mounting locations of switches S7 and S8 === | ||
+ | |||
+ | Two different mounting locations are provided on the UI PCB for S7 and S8: | ||
+ | |||
+ | | ||
+ | | ||
+ | |||
+ | "In line" is the preferred mounting location for S7 and S8. | ||
+ | |||
+ | ==== Modifications ==== | ||
+ | |||
+ | === Temporary Modification: | ||
+ | |||
+ | Symptom: In stand-by the current drawn from back-up battery is excessively high. Work-around: | ||
+ | |||
+ | === Change brightness of LEDs === | ||
+ | |||
+ | Helle LEDS: Mit den Bausatz-Vorwiderständen leuchten die LEDs sehr hell. DF9EH hat die Werte reduziert: | ||
+ | |||
+ | * R36 auf 22,6k (D1 grün) | ||
+ | * R37 auf 6,8k (D2 rot) | ||
+ | * R116 auf 6,8k (D3 blau) | ||
+ | |||
+ | \\ | ||