Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung Nächste ÜberarbeitungBeide Seiten der Revision | ||
ovi40build:uiboardbuild [17.01.2018 15:34] – df9ts_user | ovi40build:uiboardbuild [25.01.2018 15:50] – df9ts | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
+ | {{tag> | ||
- | ==== IVI40 UI Board ==== | + | ===== Building the UI V1.8 Board ===== |
- | Das UI Board beinhaltet den Hauptprozessor (MCU), Stromversorgung, | + | |
- | Auf das UI Board werden Displayboard und RFboard direkt aufgesteckt (Pfostensteckverbinder) | + | ==== OVI40 UI V1.7 Documents ==== |
- | ==== OVI40 V1.8 Bausatz ==== | + | **UI V1.7 documents are provided for information only**. Please primarily use the V1.8 documents for building the UI V1.8 board. |
- | Der Bausatz beinhaltet Bauteile in Tütchen sortiert, Leiterplatte sowie Display | + | |
- | |[{{: | + | |
+ | | ||
+ | | ||
- | {{ : | + | Please note that the component placement docs are searchable pdf documents. During soldering they can be used to quickly find a component' |
- | ==== Aufbauhinweise | + | ==== OVI40 UI V1.8 Documents |
- | < | + | |
- | < | + | |
- | < | + | |
- | ==== Unterlagen: OVI40 UI V1.7 ==== | + | * {{:projekte: |
- | UI V1.7 war die Beta Test Version der UI Platine. Es bestehen nur wenige Unterschiede zwischen V1.7 und V1.8 (der ausgelieferten Bausatz Platine). Die V1.7 Unterlagen sind deshalb interessant zum Vergleich und als Ergänzung. | + | * [[: |
+ | * {{: | ||
- | < | + | ==== OVI40 UI V1.8 Kit Contents ==== |
- | OVI40 UI V1.7 Schaltbild: {{: | + | The kit contains |
- | OVI40 UI PCB bottom layer: {{: | + | |< 60% 33% 33% 33% >| |
+ | |[{{:projekte: | ||
- | OVI40 UI PCB top layer: {{: | + | ==== Assembly and Soldering ==== |
- | ==== Unterlagen: OVI40 UI V1.8 ==== | + | The graphics below - UI V1.7 with 3.2" Display - give an impression on how the finished |
- | Im Vergleich zur V1.7 UI kommt bei der UI V1.8 folgendes dazu: | + | |
- | * unter dem Display ein weiterer zusätzlicher Taster | + | |
- | * die beiden STEP Taster unterm VFO können in zwei verschiedenen Positionen eingelötet werden. Entweder klassisch leicht nach oben versetzt wie beim mcHF oder tiefer und damit in einer Flucht mit den 6 Funktionstasten. | + | |
- | OVI40 UI BoM: [[: | + | |< 95% 50% 50% >| |
- | BoM von F4HTX Francois mit Bauteiletütchen Nummern: | + | | [{{:ovi40build:ui_top_3d.png?400|UI Board V1.7 mit 3.2" Display)}}] |
- | ==== STM32F76X_ZIT vs. STM32H743ZIT6 | + | === Please read Errata carefully |
- | Der Bausatz enthält den STM32F76X_ZIT. Der neue STM32H743ZIT6 kann eingesetzt werden, wird aber nicht mitgeliefert. | + | |
- | Die H7 - MCU wird zukünftig der Standard sein, die F7 MCU wird " | + | |
- | ==== Die UI-Platine in Betrieb nehmen ==== | + | Make sure to read the [[:ovi40build: |
- | Die UI-Platine kann (und sollte) ohne die RF-Platine zum ersten Mal in Betrieb genommen werden. Lasst das LCD zunächst weg, Jumper P6 wird gesteckt. An Pin 30 des oberen Headers wird Masse gelegt, an Pin28 +5V. Die Stromaufnahme in diesem Zustand liegt deutlich unter 80mA. Wenn nicht: Betriebsspannung sofort wieder trennen und Fehler suchen! Wenn alles ok ist, verbindet ihr die kleine USB-Buchse mit einem PC. Dieser sollte eine neue Hardwarekomponente finden (Windows) - bei Linux kann man auf der Kommandozeile mit\\ | + | |
- | //dfu-util -l//\\ | + | |
- | schauen, ob der STM32F7 angesprochen werden kann. Wenn ja, kann man die Software unter Linux nun flashen mit | + | |
- | Bootloader: //dfu-util -d -R -a 0 0483:df11 -D Pfad-zur/ | + | < |
+ | === IC Device Markings === | ||
+ | </code> | ||
- | Firmware: //dfu-util -d -R -a 0 0483:df11 -D Pfad-zur/fw-40SDR.dfu// | + | The smaller ICs can be identified by device mark. The following device marks are used: |
+ | |||
+ | |< 45% 25% 25% 25% 25% >| | ||
+ | |||
+ | |Typ |Device Mark |Schematic | ||
+ | |LP5907_Q1 | ||
+ | |BAV70 | ||
+ | |BC857B | ||
+ | |BAS85 | ||
+ | |||
+ | === MCU STM32 "Pin 1" marking === | ||
+ | |||
+ | Please understand the correct orientation of STM32 MCU Pin 1. There are two markings on the IC. Please not the text printed on MCU to find the correct Pin 1: When reading the text Pin 1 is on bottom left corner. | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | < | ||
+ | === STM32F76X_ZIT vs. STM32H743ZIT6 === | ||
+ | </code> | ||
+ | |||
+ | The kit is shipped with STM32F76X_ZIT (" | ||
+ | |||
+ | Comparison of MCUs: | ||
+ | |||
+ | |< 90% 25% 25% 25% 25% >| | ||
+ | |||
+ | | | ||
+ | | | ||
+ | |Flash[kB] | ||
+ | |RAM [kB] |192 |512 |1024 | | ||
+ | |Clock[MHz] | ||
+ | |FPU |single | ||
+ | |Pins |100 |144 |144 | | ||
+ | |DMIPS | ||
+ | |||
+ | === EEPROM IC7 orientation === | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | This is where the dot is printed. Also the edge of the case is slanted near the 1-4 pins. See [[http:// | ||
+ | |||
+ | === Prevent short cut with back up battery holder === | ||
+ | |||
+ | One of the connection pins of the battery holder might touch ground connection of a rotary encoder. Make sure to cut this pin flush with PCB surface **before soldering** | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | === Polarised capacitors === | ||
+ | |||
+ | Please observe mounting orientation of tantal and electrolytic capacitors. Markings on the capacitors are explained [[http:// | ||
+ | |||
+ | === Mounting locations of switches S7 and S8 === | ||
+ | |||
+ | Two different mounting locations are provided on the UI PCB for S7 and S8: | ||
+ | |||
+ | * "mcHF style": | ||
+ | * "OVI40 style": | ||
+ | |||
+ | "In line" is the preferred mounting location for S7 and S8. | ||
+ | |||
+ | ==== Modifications ==== | ||
+ | |||
+ | === Temporary Modification: | ||
+ | |||
+ | Symptom: In stand-by the current drawn from back-up battery is excessively high. Work-around: | ||
+ | |||
+ | === Change brightness of LEDs === | ||
+ | |||
+ | Helle LEDS: Mit den Bausatz-Vorwiderständen leuchten die LEDs sehr hell. DF9EH hat die Werte reduziert: | ||
+ | |||
+ | * R36 auf 22,6k (D1 grün) | ||
+ | * R37 auf 6,8k (D2 rot) | ||
+ | * R116 auf 6,8k (D3 blau) | ||
+ | |||
+ | \\ | ||
- | Unter Windows macht man das gleiche mit dem Tool "DfuSE Demo" von STM.\\ | ||
- | [[https:// | ||
- | Wenn der Vorgang erfolgreich war, trennt man die Betriebsspannung wieder, entfernt den Jumper P6, steckt das LCD in seine Fassung und legt die Betriebsspannung wieder an. Die Firmware sollte nun booten (klar: mit Fehlermeldungen - weil keine RF-Platine dran ist) und sich mit dem bekannten UHSDR-Bildschirm melden. | ||