Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen angezeigt.
Beide Seiten der vorigen Revision Vorhergehende Überarbeitung Nächste Überarbeitung | Vorhergehende Überarbeitung Nächste ÜberarbeitungBeide Seiten der Revision | ||
ovi40_uiboardtest [15.01.2018 10:05] – df9ts | ovi40test:uiboardtest [18.01.2018 23:59] – df9ts | ||
---|---|---|---|
Zeile 1: | Zeile 1: | ||
+ | {{tag> | ||
- | ==== Flashen des UI Boards ==== | + | ===== UI Board Test & Fehlersuche |
- | + | ||
- | STM bootloader geflasht, ebenfalls die Firmware über Dfu (mit 5 Volt Pin 28+ 30 Gnd) | + | |
- | + | ||
- | Dfuse hat das Board über USB immer noch nicht erkannt. | + | |
- | Band - hast du dazu gedrückt wenn du die 5V ans UI anlegst ? | + | |
- | Sonst geht es nicht und der USB Port erkennt KEIN STM Device in DFU Mode | + | |
- | + | ||
- | ==== UI Board Test & Fehlersuche ==== | + | |
die MCU hat zwei (!) Pin 1 Markierungen | die MCU hat zwei (!) Pin 1 Markierungen | ||
< | < | ||
Zeile 30: | Zeile 23: | ||
* R37 auf 6,8k (D2 rot) | * R37 auf 6,8k (D2 rot) | ||
* R116 auf 6,8k (D3 blau) | * R116 auf 6,8k (D3 blau) | ||
+ | |||
+ | ==== MCU wiederbeleben (" | ||
+ | If something strange or unexpected happened to your board and none of the usual procedure are working to install the Bootloader or the Firmware, this might bring life back into your UI. | ||
+ | |||
+ | You will need : | ||
+ | - an up to date STM32 ST-LINK utility ( http:// | ||
+ | - a ST-LINKV2 probe ( http:// | ||
+ | - latest version of the Bootloader and/or UHSDR Firmware | ||
+ | |||
+ | The only tricky part is to connect the probe JTAP connector to the JP8 UI board, here are the needed wires : | ||
+ | |||
+ | JP8-3 (SWDIO) to JTAG-7 | ||
+ | JP8-4 (SWCLK) to JTAG-9 | ||
+ | JP8-5 (UI_3V3) to JTAG-1 | ||
+ | JP8-6 (GND) to JTAG-20 | ||
+ | |||
+ | The rest of the procedure is straight forward : connect, erase, flash and you are done. | ||
+ | |||
+ | One additional trick, when I first connected to the MCU, I got an error message « Readout Protection Mode » and was unable to erase the chip. I finally choosed to try to flash a first time and the utility did what was necessary to remove the protection mode. Cool, thank you STM ! | ||
+ | |||
+ | [{{: | ||
+ | |||
+ | A couple of us faced the same issue during beta testing the new UI board. | ||
+ | But as you could see a cheap chinese ST Link adapter from Amazon or eBay saves your day | ||
+ | |||
+ | Here are the steps. Unfortunately in German but maybe it helps. | ||
+ | https:// | ||
+ | Register values from Andreas: | ||
+ | https:// | ||
+ | |||
+ | The URLs are from a (forgotten) I40 UI thread in the mcHF folder. | ||